Work Out Roof Pitch, Area, and Shingle Bundles
Results update as you type. Measure from the attic or the ground, never on the roof.
The calculator needs JavaScript, but the pitch table below works without it. For an exact measurement, ask our roofers:
Shingle bundles, with waste
Hip and ridge cap shingles aren't included: they're sold separately and measured in linear feet. Some brands take more than three bundles per square, so check the wrapper.
| Pitch | Angle | Area factor | 1,000 sq ft footprint |
|---|---|---|---|
| 2:12 | 9.5° | 1.014 | 1,014 sq ft of roof |
| 3:12 | 14.0° | 1.031 | 1,031 sq ft of roof |
| 4:12 | 18.4° | 1.054 | 1,054 sq ft of roof |
| 5:12 | 22.6° | 1.083 | 1,083 sq ft of roof |
| 6:12 | 26.6° | 1.118 | 1,118 sq ft of roof |
| 7:12 | 30.3° | 1.158 | 1,158 sq ft of roof |
| 8:12 | 33.7° | 1.202 | 1,202 sq ft of roof |
| 9:12 | 36.9° | 1.250 | 1,250 sq ft of roof |
| 10:12 | 39.8° | 1.302 | 1,302 sq ft of roof |
| 12:12 | 45.0° | 1.414 | 1,414 sq ft of roof |
This is a planning estimate for a simple roof. Dormers, valleys, and multiple roof sections change the numbers, so order materials from an exact measurement.
What Roof Pitch Means
Roof pitch is how steep a roof is, written as the inches it rises for every 12 inches it runs level. A 6:12 roof rises 6 inches over each foot. Pitch matters for more than looks: it decides how much roof surface there is over the same house, which materials suit the roof, and how safe it is to work on.
LOA Construction and Roofing built this calculator for homeowners, do-it-yourselfers, and anyone who wants to check a number before talking to a roofer. It does three things: works out the pitch from a measurement, converts a level footprint into the real roof area, and estimates the bundles of shingles needed.
How to Measure Your Roof Pitch Safely
You don’t need to climb on the roof, and you shouldn’t. The safest place to measure is the attic:
- Hold a level horizontally against the bottom of a rafter.
- Mark 12 inches along the level from where it touches the rafter.
- Measure straight up from that mark to the underside of the rafter. That’s your rise.
If you can’t measure over a full 12 inches, measure over any level distance and enter both numbers. The calculator converts them, so 3 inches over 6 inches is the same 6:12 pitch.
How Roof Area Is Worked Out
A sloped roof has more surface than the level area it covers. The calculator multiplies the footprint under the roof by a slope factor for your pitch. That factor is the length of roof over one foot of level run: the square root of 1 plus (pitch ÷ 12) squared.
For example, a 6:12 roof has a factor of about 1.118, so a 2,000 sq ft footprint carries about 2,236 sq ft of roof. The table under the calculator shows the factor for common pitches. These match the slope factors shingle makers publish, such as IKO’s 1.054 for a 4:12 roof and 1.414 for a 12:12 roof.
For the footprint, measure the house’s length and width at the edges of the roof, including the overhangs, and multiply. On a two-story house, use the footprint, not the total living area.
How Many Bundles of Shingles You Need
Shingles are sold by the square, which covers 100 square feet of roof. According to IKO, most popular shingles take three bundles per square, though some brands need more, so check the wrapper.
You’ll also need extra for waste: shingles cut to fit at edges, valleys, and around vents. IKO suggests about 10% to 15% as a general range, and smaller roofs tend to waste more. The calculator rounds up to whole bundles. Hip and ridge cap shingles are sold separately and measured in linear feet, so they’re not in the count.
Here’s a worked example: 2,000 sq ft of footprint at 6:12 is about 2,236 sq ft, or 22.4 squares. At three bundles per square plus 10% waste, that’s 74 bundles.
When the Simple Math Isn’t Enough
The calculator assumes one roof plane at one pitch, which works for planning and for simple gable and hip roofs. Real roofs often have several sections at different pitches, dormers, valleys, and skylights, and each one changes the material count. For ordering materials or comparing bids, an exact measurement is worth having.
If you’re pricing a new roof rather than buying materials, our roof replacement cost calculator gives a price range from your home’s size, pitch, and material. Not sure which material fits your roof? Our roof material quiz compares your options, and our page on asphalt shingle roofs covers what to know about shingles in Central Texas. Very low-slope roofs usually need different materials than shingles; our flat roofing page explains the options.
Get an Exact Measurement
LOA offers no-cost, same-day roof inspections, and drone inspections when you can’t be there. We’ll measure your roof, check its condition, and give you an honest estimate, with no pressure to buy. You call the shots from there.
Schedule a free inspection with LOA, your local Austin roofing company, or call us at (512) 375-3654.
Frequently Asked Questions
How Do I Find My Roof Pitch Without Climbing on the Roof?
Measure it from the attic. Hold a level against a rafter, mark 12 inches along it, and measure straight up to the rafter. That number is the rise, and the pitch is that rise over 12.
How Many Square Feet Does a Bundle of Shingles Cover?
For most popular shingles, three bundles cover one square, or 100 square feet, so each bundle covers about 33 square feet. Some brands differ, so check the coverage printed on the wrapper.
How Much Extra Shingle Should I Order for Waste?
About 10% to 15% is a general range. Simple roofs with few cuts sit at the low end; roofs with valleys, dormers, or many sections need more, and smaller roofs tend to waste a higher share.